Solar power works well for most items, except large electric appliances that use an electric heat element such as a water heater, clothes dryer and electric stove, for example, or total electric home heating systems. It is not cost effective to use solar power for these items.

Conversion to natural gas, propane or other alternatives is usually recommended. Solar power can be used to operate a gas clothes dryer (Maytag, etc) because the electrical requirement is limited to the drum-motor and/or ignito-lighter, but not a heating element for drying the clothes, for example.

The basics of solar power:

Using solar power to produce electricity is not the same as using solar to produce heat. Solar thermal principles are applied, to produce hot fluids or air. Photovoltaic principles are used to produce electricity. A solar panel (PV panel) is made of the natural element, Silicon, which becomes charged electrically when subjected to sunlight.

Solar panels are directed at solar south in the northern hemisphere and solar north in the southern hemisphere. These are slightly different from magnetic compass north and south directions, at an angle dictated by the geographic location and latitude of where they are to be installed.

Typically, the angle of the solar array is set within a range of between site latitude plus 15 degrees and site latitude minus 15 degrees, depending on whether a slight winter or summer bias is desirable in the system. Many solar arrays are placed at an angle equal to the site latitude, with no bias for seasonal periods.

This electrical charge is consolidated in the PV panel and directed to the output terminals, to produce low voltage (Direct Current) which is usually 6 to 24 volts. The most common output is intended for nominal 12 volts, with an effective output usually up to 17 volts. A 12 volt nominal output is the reference voltage, but the operating voltage can be 17 volts or higher, much like your car alternator charges your 12 volt battery at well over 12 volts. So there's a difference between the reference voltage and the actual operating voltage.

The intensity of the Sun's radiation changes with the hour of the day, time of the year and weather conditions. To be able to make calculations in planning a system, the total amount of solar radiation energy is expressed in hours of full sunlight per m², or Peak Sun Hours. This term, Peak Sun Hours, represents the average amount of sun available per day throughout the year.

It is presumed that at "peak sun", 1000 W/m² of power reaches the surface of the earth. One hour of full sun provides 1000 Wh per m² = 1 kWh/m², representing the solar energy received in one hour, on a cloudless summer day, on a one square meter surface, directed towards the sun. To put this in another perspective, the United States Department of Energy indicates that the amount of solar energy that hits the surface of the earth every +/- hour, is greater than the total amount of energy that the entire human population requires in a year. Another perspective is that roughly 100 square miles of solar panels placed in the southwestern U.S. could power the country.

The daily average Peak Sun Hours, based on either full year statistics, or average worst month of the year statistics, for example, is used for calculation purposes in the design of the system.

So it can be concluded that the power of a system varies, depending on the intended geographical location. People in the Northern parts of Africa, where it is very warm, will need less solar panels than those living in say, the Northern parts of America, where it is cooler, to produce the same amount of power.

Components used to provide solar power:

The four primary components for producing electricity using solar power, which provides common 120 volt AC power for daily use are: Solar panels, charge controller, battery and inverter. Solar panels charge the battery, and the charge regulator insures proper charging of the battery. The battery provides DC voltage to the inverter, and the inverter converts the DC voltage to normal AC voltage. If 240 volts AC is needed, then either a transformer is added or two identical inverters are series-stacked to produce the 220/240 volts.

Charge Controller:

A charge controller monitors the battery's state of charge, to insure that when the battery needs charge current, it gets it, and also insures that the battery isn't over charged. Connecting a solar panel to a battery, without a regulator, seriously risks damaging the battery and potentially causes a safety concern.

Charge controllers, or often called charge regulators, are rated, based on the amount of amperage they can process from a solar array. If a controller is rated at 20 amps, it means that you can connect up to 20 amps of solar panel output current to this one controller.

The most advanced charge controllers utilize a charging principal referred to as Pulse Width Modulation (PWM), which insures the most efficient battery charging and extends the life of the battery. Even more advanced controllers also include Maximum Power Point Tracking (MPPT), which maximizes the amount of current going into the battery from the solar array, by lowering the panel's output voltage, which increases the charging amps to the battery, because if a panel can produce 60 watts with 17.2 volts and 3.5 amps, then if the voltage is lowered to say 14 volts, then the amperage increases to 4.28 (14v X 4.28 amps = 60 watts) resulting in a 19% increase in charging amps for this example.

Many charge controllers also offer Low Voltage Disconnect (LVD) and Battery Temperature Compensation (BTC) as an optional feature. The LVD feature permits connecting loads to the LVD terminals, which are then voltage sensitive. If the battery voltage drops too far, the loads are disconnected, preventing potential damage to both the battery and the loads. BTC adjusts the charge rate, based on the temperature of the battery, since batteries are sensitive to temperature variations above and below about 75 F degrees.


The Deep Cycle batteries used are designed to be discharged and then recharged hundreds or thousands of times. These batteries are rated in Amp Hours (ah), usually at 20 hours and 100 hours. Simply stated, amp hours refers to the amount of current, in amps, which can be supplied by the battery over the period of hours. For example, a 350ah battery could supply 17.5 continuous amps over 20 hours, or 35 continuous amps for 10 hours. To quickly express the total watts potentially available in a 6 volt 360ah battery; 360ah times the nominal 6 volts equals 2160 watts or 2.16kWh (kilowatt-hours). Like solar panels, batteries are wired in series and/or parallel, to increase voltage to the desired level and increase amp hours.

The battery should have sufficient amp hour capacity, to supply needed power during the longest expected period "no sun" or extremely cloudy conditions. A lead-acid battery should be sized at least 20% larger than this amount. If there is a source of back-up power, such as a standby generator along with a battery charger, the battery bank does not have to be sized for the worst case weather conditions.

The size of the battery bank required, will depend on the storage capacity required, the maximum discharge rate, the maximum charge rate, and the minimum temperature at which the batteries will be used. During planning, all of these factors are looked at, and the one requiring the largest capacity will dictate the battery size.

One of the biggest mistakes made by those just starting out, is not understanding the relationship between amps and amphour requirements of 120 volt AC items, versus the effects on their DC low voltage batteries.

For example, say you have a 24 volt nominal system and an inverter powering a load of 3 amps, 120VAC, which has a duty cycle of 4 hours per day. You would have a 12 amp hour load (3A X 4 hrs=12 ah). However, in order to determine the true drain on your batteries, you have to divide your nominal battery voltage (24v) into the voltage of the load (120v), which is 5, and then multiply this times your 120vac amp hours (5 x 12 ah). So in this case the calculation would be 60 amp hours drained from your batteries, not the 12 ah. Another simple way is to take the total watt-hours of your 120VAC device and divide by nominal system voltage. Using  the above example; 3 amps x 120 volts x 4 hours = 1440 watt-hours divided by 24 DC volts = 60 amp hours.

Lead-acid batteries are the most common in PV systems, because their initial cost is lower and because they are readily available nearly everywhere in the world. There are many different sizes and designs of lead-acid batteries, but the most important designation is that they are deep cycle batteries. Lead-acid batteries are available in both wet-cell, which requires maintenance, and sealed non-maintenance versions. AGM and Gel-cell deep-cycle batteries are also popular, because they are maintenance free and they last a lot longer.

Using an Inverter:

An inverter is a device which changes DC power stored in a battery, to standard 120/240 VAC electricity (also referred to as 110/220). Most solar power systems generate DC current, which is stored in batteries. Nearly all lighting, appliances, motors, etc., are designed to use ac power, so it takes an inverter to make the switch from battery stored DC, to standard power 120 VAC, 60 Hz.

In an inverter, direct current (DC) is switched back and forth, to produce alternating current (AC). Then it is transformed, filtered, stepped, etc. to get it to an acceptable output waveform. The more processing, the cleaner and quieter the output, but the lower the efficiency of the conversion. The goal becomes to produce a waveform that is acceptable to all loads, without sacrificing too much power in the conversion process.

Inverters come in two basic output designs - sine wave and modified sine wave. Most 120VAC devices can use the modified sine wave, but there are some notable exceptions. Devices such as laser printers, which use triacs and/or silicon controlled rectifiers, are damaged when provided mod-sine wave power. Motors and power supplies usually run warmer and less efficiently on mod-sine wave power. Some things, like fans, amplifiers, and cheap fluorescent lights, give off an audible buzz on modified sine wave power. However, modified sine wave inverters make the conversion from DC to AC very efficiently. They are relatively inexpensive and many of the electrical devices we use every day, work fine on them.

Sine wave inverters can virtually operate anything. Your utility company provides sine wave power, so a sine wave inverter is equal to, or even better than utility supplied power. A sine wave inverter can clean up utility or generator supplied power, because of it's internal processing.

Inverters are made with various internal features and many permit external equipment interface. Common internal features are internal battery chargers, which can rapidly charge batteries when an AC source such as a generator or utility power is connected to the inverter's INPUT terminals. Auto-transfer switching is also a common internal feature, which enables switching from either one AC source to another and/or from utility power to inverter power for designated loads.

Battery temperature compensation, internal relays to control loads, automatic remote generator starting/stopping and many other programmable features are available.

Most inverters produce 120VAC, but can be equipped with a step-up transformer, to produce 120/240VAC. Some inverters can be series or parallel stacked-interfaced, to produce 120/240VAC, or to increase the available amperage.

Efficiency Losses:

In all systems there are losses, due to such things as voltage losses as the electricity is carried across the wires, batteries and inverters not being 100 percent efficient, and other factors. These efficiency losses vary from component to component and from system to system and can be as high as 25 percent. That's why it's a good idea to speak to someone who has extensive design experience, to properly configure the right equipment for you.

Why not get started on your own alternative energy devices, to save yourself a fortune and decrease your reliance on the utility company It's not as difficult, or as expensive as you may think. You can build your own solar panel at home, for under $200. See more by clicking here, or copy this link:

On our website AltPower, we have a huge directory of the best resources available on the internet. There are books, plans, designs and more. Take a look here: